What are the installation steps for the water purifier?
2023-09-03 14:10:17
What are the installation steps for the water purifier?
Compared with the water purifier in the kitchen, the installation procedure of another type of common kitchen water treatment equipment-pure water machine is much more complicated. What are the installation steps of the pure water machine? Today, Jiu Zheng Xiaobian compiled the knowledge of the installation steps of the pure water machine according to the installation practice. I hope to help you understand more about the pure water machine.
The kitchen water purifier installation steps and processes mainly include:
1. Turn off the water source, turn on the faucet, and let go of the remaining water in the tube.
2. Remove the faucet inlet pipe, install the water inlet tee and tighten with a wrench. Install the 1|4 inlet ball valve wrapped around the raw material belt to the side hole of the inlet tee, and install the tap water inlet pipe on the inlet tee. And tighten with a wrench.
3. Close the inlet ball valve, open the water source, and wipe it with a paper towel to check if the fitting is water seepage.
4. Put the three filters of PP cotton, granular activated carbon and compressed activated carbon into the filter bottle in sequence, and tighten the screw caps of each level with a wrench.
5. Wrap an appropriate amount of raw material tape at the outlet of the pressure tank, install the pressure tank ball valve, and connect the rear activated carbon water inlet to the pressure tank water outlet ball valve with PE pipe.
6. Inlet pipe connection: When installing the machine under the water purifier, directly connect the pipeline connected to the inlet ball valve to the inlet of the first-stage filter bucket of the machine; when installing the cabinet, first open the lower part of the cabinet. The hole cover of the pipeline and the inlet and outlet of the electric wire, take out the power cord and pass the pipe connected to the water ball valve through the hole, lead it into the cabinet and connect it to the water inlet joint of the first stage filter bucket of the machine, and then check whether the joint is seeping water. .
7. Flush the pre-filter: first remove the reverse osmosis membrane shell into the water short PT tube, insert it into a container, open the water source and power supply, rinse the first three filter elements, and directly to the clear water.
8. Install the gooseneck faucet: use a steel nail to make a small groove on the stainless steel "target=_blank> stainless steel hand basin (for easy drilling), and drill the hole on the groove with a hand drill (M12 drill). Then fix the goose. The neck faucet, the gooseneck faucet is connected to the 1|4PE pipe at the lower end, and the other end is connected to the rear activated carbon filter outlet.
9. Remove the RO membrane cover with the template shell wrench, install the RO membrane and the RO membrane cover, and tighten the membrane cover with a wrench.
10. Take an appropriate amount of 1|4PE line to connect the waste water port and introduce it into the lower water pipe.
11. Turn on the water source and the gooseneck faucet to check if the high pressure pump is working properly. After the gooseneck faucet is out of water, close the gooseneck faucet. After 5 minutes, check whether the parts are seeping water. All the installations are completed.
Since the installation of the kitchen water purifier is very professional, it is recommended that the owner should find a professional installer to install the pure water machine when installing the pure water machine in the kitchen to ensure the installation quality and ensure the water treatment capacity. With quality.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Compared with the water purifier in the kitchen, the installation procedure of another type of common kitchen water treatment equipment-pure water machine is much more complicated. What are the installation steps of the pure water machine? Today, Jiu Zheng Xiaobian compiled the knowledge of the installation steps of the pure water machine according to the installation practice. I hope to help you understand more about the pure water machine.
The kitchen water purifier installation steps and processes mainly include:
1. Turn off the water source, turn on the faucet, and let go of the remaining water in the tube.
2. Remove the faucet inlet pipe, install the water inlet tee and tighten with a wrench. Install the 1|4 inlet ball valve wrapped around the raw material belt to the side hole of the inlet tee, and install the tap water inlet pipe on the inlet tee. And tighten with a wrench.
3. Close the inlet ball valve, open the water source, and wipe it with a paper towel to check if the fitting is water seepage.
4. Put the three filters of PP cotton, granular activated carbon and compressed activated carbon into the filter bottle in sequence, and tighten the screw caps of each level with a wrench.
5. Wrap an appropriate amount of raw material tape at the outlet of the pressure tank, install the pressure tank ball valve, and connect the rear activated carbon water inlet to the pressure tank water outlet ball valve with PE pipe.
6. Inlet pipe connection: When installing the machine under the water purifier, directly connect the pipeline connected to the inlet ball valve to the inlet of the first-stage filter bucket of the machine; when installing the cabinet, first open the lower part of the cabinet. The hole cover of the pipeline and the inlet and outlet of the electric wire, take out the power cord and pass the pipe connected to the water ball valve through the hole, lead it into the cabinet and connect it to the water inlet joint of the first stage filter bucket of the machine, and then check whether the joint is seeping water. .
7. Flush the pre-filter: first remove the reverse osmosis membrane shell into the water short PT tube, insert it into a container, open the water source and power supply, rinse the first three filter elements, and directly to the clear water.
8. Install the gooseneck faucet: use a steel nail to make a small groove on the stainless steel "target=_blank> stainless steel hand basin (for easy drilling), and drill the hole on the groove with a hand drill (M12 drill). Then fix the goose. The neck faucet, the gooseneck faucet is connected to the 1|4PE pipe at the lower end, and the other end is connected to the rear activated carbon filter outlet.
9. Remove the RO membrane cover with the template shell wrench, install the RO membrane and the RO membrane cover, and tighten the membrane cover with a wrench.
10. Take an appropriate amount of 1|4PE line to connect the waste water port and introduce it into the lower water pipe.
11. Turn on the water source and the gooseneck faucet to check if the high pressure pump is working properly. After the gooseneck faucet is out of water, close the gooseneck faucet. After 5 minutes, check whether the parts are seeping water. All the installations are completed.
Since the installation of the kitchen water purifier is very professional, it is recommended that the owner should find a professional installer to install the pure water machine when installing the pure water machine in the kitchen to ensure the installation quality and ensure the water treatment capacity. With quality.
Http://news.chinawj.com.cn Editor: (Hardware Business Network Information Center) http://news.chinawj.com.cn
Stainless steel round steel belongs to a class of long wood, also belongs to a class of bar, the so-called stainless steel round steel refers to the cross section of uniform circular long wood, generally about four meters long. It can be divided into light circles and black rods. The so-called light circle, refers to the smooth surface, after the quasi-rolling treatment; And the so-called black rod, refers to the surface of the black thick, hot rolled directly.
Stainless steel round steel can be divided into hot rolling, forging and cold drawing according to the production process. Hot rolled stainless steel round steel is 5.5-250 mm in size. Among them :5.5-25 mm small stainless steel round steel mostly to straight strips in bundles supply, commonly used for reinforcing bars, bolts and various mechanical parts; Stainless steel round steel greater than 25 mm, mainly used in the manufacture of machine parts or seamless steel pipe billets.
Stainless steel round steel has broad application prospects, and is widely used in hardware kitchenware, shipbuilding, petrochemical, machinery, medicine, food, power, energy, aerospace, building decoration. Seawater equipment, chemical, dye, paper, oxalic acid, fertilizer and other production equipment; Photography, food industry, coastal facilities, ropes, CD rods, bolts, nuts.
316 Stainless Steel Round Rod,316 Stainless Steel Bar,316 Stainless Steel Rod,Ss Stainless Steel Rod
Shandong Xinsuju Steel Co.,Ltd. , https://www.sawlpipe.com