New anti-rust technology in fine bearing process
2023-05-11 12:11:46
| Home>Bearing knowledge> New technology for anti-rust between fine bearing processes |
New anti-rust technology in fine bearing process
Source: Bearing network time: 2013-05-03
| /*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089'; |
Bearing anti-rust operation is an important operation; especially the anti-rust between processes; like the bearing is washed, removed, and ground in the heat treatment workshop; there are many processes. When the product is not produced by running water; The end of the sequence processing is stored in the central warehouse; therefore, the bearing rings stored between the processes need to be rust-proof.
Traditional rust prevention methods and their lack of rust prevention between bearing processes are generally selected as follows:
1. Immerse in the anti-rust tank to immerse the bearing in the aqueous solution of 5% sodium nitrite and 0.6% sodium carbonate; the anti-rust effect is good; but many anti-rust tanks and other equipment; occupy a lot of space; .
2. Dip the concentrated sodium nitrite solution to remove the product; immerse it in a solution rich in 15%-20% sodium nitrite and 0.6% sodium carbonate; then stack it up. Use this method to prevent rusting period Short; usually only for 7-14 days; and in the rainy season; because the climate is humid; only 2-3 days can be re-processed; demand costs labor and money.
3. Oil-coated products are coated with anti-rust oil. This method is necessary to remove before performing the next process;
The analysis of the new anti-rust process has been tackled by the relevant manufacturers; the production practice has been marked for many years; the anti-rust between the processes has been improved repeatedly; the anti-rust effect of the spray-jet type is better than that. The trial of the anti-rust of the roller is started; The semi-products and products were washed once a day with an aqueous solution of sodium nitrite; after 3 months, no rust was found in the results of the test; now the rust-proof rust is used for the semi-products of the bearing scam; the effect is also the same. The rust-proof rust-proof process is simpler; The method is as follows:
1. The purchase and construction of equipment depends on how much semi-products are stored; a central repository is established; a cement floor is used on the ground; a walkway can be set up in the center; about 1.5 m; a trolley used to pass the bearing ring. A nitrous acid is placed at the end of the passage. Sodium solution pool; solution formulation is 5%-10% sodium nitrite plus 0.6% sodium carbonate; and the backwater drain is made on the ground; then the bearing rings are stacked on both sides of the floor; each pile of bearing rings There is a 0. 6m walkway between them. The central library can be described as about 64m2; its sodium nitrite aqueous solution pool is 1m3.
2. The process is washed once a day with an aqueous solution of sodium nitrite; the aqueous solution is sucked from the pool by a water pump; the rubber pipe is passed to the shower head; the bearing ring is flushed like a shower. The washed aqueous solution flows back to the pool from the backwater channel; Back to the upper end of the water pool; use a fine wire mesh and gauze to make a filter mesh to the textile ash and dirt into the pool. The central library should be quality and hygienic.
The solution in the pool is tested every 2 days; it is compensated according to the results of the test; the replacement period of the solution in the pool is carried out in different months; the exchange is completely exchanged every 2 weeks from April to September; the monthly exchange is from October to March; once.
It is more convenient to handle the rust-proof type; it is more convenient to handle; it saves labor; it can't be finished with 2 small rust prevention in the central warehouse; now it can also do other operations with one person; it is also obvious from the rust prevention effect. In March 2003, more than 4,000 rolls of 7002136 and 3620 were used; the rust-proof rust was selected; for nearly a year, it was still very bright; there was no rust. In addition, the consumption of chemicals was also greatly saved; The roller workshop costs more than 4,000 kilograms of sodium nitrite per month; today it only uses 200 kilograms; it saves nearly half.
The spray-type rust-proof method has passed the experiment and application of related manufacturers in recent years; it proves that it is suitable for medium and large-sized, large-volume, long-cycle bearing semi-products.
Recommend to friends comments close window
| Bearing related knowledge |
| Powder metallurgy oil bearing NSK imported bearings in the anti-wear bearing protection and smooth bearing equipment selection method to open the vibrating screen bearing how to correctly install the thrust (positioning) bearing |
This article links to http://
Please indicate China Bearing Network http://
Previous:The grease is a small common sense in a humid environment. Next: Casting heat treatment
Aluminum oxide flap discs are made by Aluminum oxide coated cloth, one kind of the flap discs or power flex discs. ALO flap discs have the advantages of grinding discs and fiber discs, making it easier for grinding and polishing disposable, reducing the work process and lower the grinding cost.
Abrasive grains for ALO Flap Disc is Aluminum oxide. ALO flap discs are widely used in grinding, polishing and deburrnig of metals and non-metals; metals includes general metals, carbon steel, alloy steel, casting iron, etc.
Flap discs have the features of quick speed, high efficiency, synchronous consumption, strong grinding force, fast heat disspation and good performance.
Aluminum Oxide Flap Disc,Aluminium Oxide Flap Disc,Flap Wheel For Aluminum,Best Flap Disc For Aluminum
Henan Yuteng Abrasives Co.,Ltd , https://www.henanyutengabrasives.com